Hesse FANTASTIC-COLOR DB 4888x(gloss level)-(colour)

  • Up to 60 % more material can be applied on vertical surfaces in comparison with standard PU colour lacquers
  • 40 % higher opacity across all colour tones and up to 25 % higher solids content in comparison with UNA-COLOR
  • can be directly applied onto MDF edges
  • good metal-marking resistance; a transparent top coat can be omitted in many cases
FANTASTIC-COLOUR is a light fast and very well-balanced two-component colour lacquer with impressive opacity and fast drying. The product’s particular distinguishing features are its outstanding ability to stay on vertical surfaces together with excellent levelling on horizontal surfaces. FANTASTIC-COLOUR is suitable for top coating and is therefore the right colour lacquer for very sophisticated and high-quality colour lacquer finishes with an impressive feel and metal marking resistance. FANTASTIC-COLOR can also be applied directly onto sanded, bare MDF edges and surfaces.
Request product Download data sheet
  • Description
  • Information on use
  • Sample process
  • Safety Data Sheets / Certificates

Fields of application

FANTASTIC-COLOR meets the highest colour lacquer demands in every relevant product feature and can be used for all interior fittings, including kitchens and bathrooms and for coating the interior fixtures aboard vessels.

Technical specifications

Appearance opaque
Flow time (+/- 15 %) 31 s / DIN 53211 - 6 mm
Form of delivery fluid
VOC EU % 52.09 %
Number of coats (max) 4
Amount per layer (minimum) 80 g/m²
Amount per layer (max) 180 g/m²
Total application volume 600 g/m²
Mixing ratio (by volume) 10 : 1 PU Hardener DR 4071
Mixing ratio (gravimetric) 100 : 8 PU Hardener DR 4071

Information on use

Usage time 6 h / 20 °C
Pot life 6 h / 20 °C
Drying 2 h / 20 °C
Stackable after > 16 h / 20 °C
Complete drying 7 d / 20 °C
Surface preparation Clean, dry wood, depending on species and application method. Perform cleaning by sanding on foil or melamine before coating.
Substrate sanding grits from-to 150 - 320
Lacquer sanding (grit) from - to 320 - 400
Finishing Fundamentally on its own. Should absolute metal marking and colour abrasion resistance or a different gloss level be required, then we recommend top coating with a transparent and light fast PU Multicoat lacquer up to gloss level satin (40 - 59 gloss), e.g. using Hesse UNA-PUR DE 55x(gloss level) / DE 4259x(gloss level), Hesse MEGA-PUR DE 56x(gloss level) / DE 4503x(gloss level) or PU NANO-TOP DU 520 / DU 4554x(gloss level). If necessary, after a drying time of > 6 h / 20 °C, FANTASTIC-COLOR can be recoated using the following Hesse high gloss systems: ADAMANT DU 48889, PU Brillant Lacquer DU 46269-0005, PU Brillant-Colour DB 44099-(colour tone) and HYDRO-PU Brillant Lacquer HDE 54799.
Comments on sanding In case of direct coating on cleaned and sanded foils, please make a test coating to check the adhesion!
Yield per coat 0 - 0 m²/l

The spreading rate is heavily dependent on the type of application. The specifications relate to a liter of ready-for-use product, if necessary including hardener and thinner.
Storage temperature 16 - 40 °C
Working temperature 20 °C
Working viscosity 22 s in 4mm
Processing instructions Hardening at 5 : 1 with PU Hardener DR 4076-0001 after previously mixing in 5 % Glass lacquer additive EL 460-0025 with the lacquer components also enables direct coating on glass after it has been properly cleaned. For cleaning glass surfaces before application we recommend Hesse Cleaning thinner ZD 101. FANTASTIC-COLOR with a mixing ratio (by volume) of 10 : 1 can also be applied using DR 470 / DR 4070.Direct application on untreated MDF should only be carried out with a mixing ratio (by volume) of 10 : 1 with PU Hardener DR 4071!
Particular instructions For MDF substrates: With MDF coatings, you can avoid painting faults and edge breaks if you observe the following: Selection of an MDF quality suitable for the field of application, see manufacturer data on EU standard EN 622-5 pt.4 Test methods EN 317 (requirements on thickness swelling). Ideal panel moisture 5 - 7 %. If possible coat the MDF all around, the backs should at least receive a clear coating. Avoid sharp edges and milling grooves, round-off wherever possible. Coat edges and milling grooves 2 x with primer, do not sand through, if need be, prime again. Thick boards that have been built by gluing together several thinner boards are, due to the variance in tension, susceptible to edge ridging. It is better to select a single MDF board of the appropriate thickness. Panels that have been glued together should always be sanded flat at the edges and colourlessly pre-insulated. Any water introduced by the gluing process must be allowed to evaporate prior to coating. Store filler-coated surfaces in an air conditioned location and apply the final coat in a timely manner.
“A risk assessment was undertaken according to Directive 2014/90/EU, Annex II, Section 3. This coating does not pose a physical risk to health nor a risk to the environment when cured and dried.”
General instructions on workmanship PU lacquers should not be applied and dried at material and room-temperatures below 18 °C and 40 % RH. Ideal values are: 20 - 25 °C, 50 - 65 % RH. Deviations will result in drying or hardening errors. In order to avoid adhesion problems, please sand the PU lacquered surfaces before applying fresh lacquer and apply lacquer to the sanded surfaces as soon as possible. Old lacquer and hardener mixtures affect the surface quality (adhesion/resistance). Freshly bleached substrates must undergo intermediate drying for at least 48 h at 20 °C before coating with suitable PU lacquers. If stored correctly (at least 20 °C room temperature), the final hardness of the coating is achieved after a week.
Please apply a test coat under real conditions!

Laminated MDF cabinet front in RAL 9016, matt
Surface sanding: 320 - 400 grit (dust removal)
Edge and profile sanding: 150 - 180 grit (dust removal)
Basecoat: 1 x 150 - 200 g/m² Hesse FANTASTIC-FILL DP 4755-9343, mixing ratio (by volume) 10 : 1 with PU Hardener DR 4071 / DV 471 and addition of 15 % DV 4900 / DV 490 Thinner to the lacquer/hardener mixture
Drying: > 2 h / 20 °C, preferably 16 h / 20 °C
Filler sanding: 320 - 400 grit (dust removal)
Basecoat: 1 x 150 - 200 g/m² Hesse FANTASTIC-FILL DP 4755-9343, mixing ratio (by volume) 10 : 1 with PU Hardener DR 4071 / DV 471 and addition of 15 % DV 4900 / DV 490 Thinner to the lacquer/hardener mixture
Drying: > 2 h / 20 °C, preferably 16 h / 20 °C
Filler sanding: 320 - 400 grit (dust removal)
Colour and top coat: 1 x 120 - 180 g/m² Hesse FANTASTIC-COLOR DB 48882-9016, mixing ratio (by volume) 10 : 1 with Hesse PU Hardener DR 4071 / DR 471 and addition of 10 - 30 % DV 4900 / DV 490 Thinner to the lacquer/hardener mixture
Complete drying: > 16 h / 20 °C

Contact

Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.