Hesse PURA-NATURA HDE 52-0

  • Light-fast
  • Dull matt with good scratch resistance
  • Natural wood effect
PURA-NATURA is convincing due to its dull matt natural wood effect, which ensures that the natural accentuation of the wood is retained. The surface provides high scratch resistance with very good resistance to tread marks and common household chemicals. This brightening and light fast 2C multicoat lacquer is suitable for priming and top coating light woods and its DIBt approval makes it especially suitable for staircases and wooden floors.
Request product Download data sheet
  • Description
  • Information on use
  • Sample process
  • Safety Data Sheets / Certificates

Fields of application

In living areas, and also in higher strain areas of parquet and wooden flooring. Can also be used on bleached surfaces (that are adequately dry).

Technical specifications

Giscode W3/DD+
Appearance colourless
Decopaint basis WB
Decopaint category J
Density series kg/l 1.024
Flow time (+/- 15 %) 35 s / DIN EN ISO 2431 - 4 mm
Form of delivery fluid
Non-volatile content series % 29
Profile of properties Brightening
VOC EU % 6.05 %
Number of coats (max) 2
Amount per layer (minimum) 80 g/m²
Amount per layer (max) 100 g/m²
Total application volume 200 g/m²
Mixing ratio (by volume) 10 : 1 PURA-NATURA Hardener HDR 72
Mixing ratio (gravimetric) 100 : 10 PURA-NATURA Hardener HDR 72

Information on use

Usage time 2 h / 20 °C
Pot life 3 h / 20 °C
Drying 3 h / 20 °C
Complete drying 7 d / 20 °C
Accessible after 8 h / 20 °C
Load bearing after 7 d / 20 °C
Surface preparation Professionally laid and prepared parquet or corresponding wooden flooring. The floor must first be sanded back to the bare wood and be dry and free from oil, grease, wax, silicones and sanding dust.
Substrate sanding grits from-to 100 - 120
Lacquer sanding (grit) from - to 120 - 150
Finishing After sufficient drying: initial care using Hesse PROTECT-CLEANER PR 90 or Hesse ANTISLIP-CLEANER PR 93.
Comments on sanding The quality and uniformity of the wood and of the lacquer sanding are crucial to the final surface finish. After sanding, remove dust as prescribed.
Yield per coat 10 - 13 m²/l

The spreading rate is heavily dependent on the type of application. The specifications relate to a liter of ready-for-use product, if necessary including hardener and thinner.
Working Temperature Range 18 - 22 °C
Storage temperature 10 - 30 °C
Working temperature 20 °C
conditions of transport 10 - 30 °C
Processing instructions The floor must first be sanded back to the bare wood and be dry and free from oil, grease, wax, silicones and sanding dust. Shake the lacquer well! Add the correct hardener to the organic lacquer container and immediately shake well for 1 - 2 min. Do not mix in the application container. The mixing ratio must also be accurately observed in the case of partial amounts, and the mixture well shaken. Press the strainer into the outlet opening, fill the lacquer / hardener mixture into a suitable application container and work from this! Only use a mixture within the given application time. Never store product mixed with hardening agent in closed containers. Do not use any electrical stirring devices; risk of forming foam or bubbles!
Particular instructions Greying may occur on dark woods or stains because of the light milky colour of the products.. In order to reduce the risk of lateral bonding, critical substrates such as wood plaster, edge lamellae, floor boards, parquet on underfloor heating, etc. require an appropriate pretreatment with HG 21 or HG 22. If using particularly tannin-rich woods, we recommend using basecoat HG 22 or HG 24. To avoid the possibility of staining, please only renovate parquet flooring, which was previously treated with solvent-based systems, with solvent-based systems again! Shake the lacquer well! Spraying: possible; however the addition of water is required. When the hardening agent is well worked in, adjust the spraying viscosity with up to 5 % water. Personal protective equipment and adherence to the instructions for the spraying application. Press the strainer into the outlet opening, fill the lacquer / hardener mixture into a suitable application container and work from this! Only use a mixture within the given application time. Never store product mixed with hardening agent in closed containers. Do not use any electrical stirring devices; risk of forming foam or bubbles! Clean work equipment with water. Dried lacquer residue can be removed with Hesse CLEANING-AGENT DV 9. Films or carpets must not be placed on the parquet flooring until it has completely hardened.
General instructions on workmanship
The moisture content should be between 8 - 12 %. Please do not use and dry HYDRO lacquers at material and room temperatures below 18 °C. The ideal humidity for painting is between 55 and 65 %. In order to avoid problems with bonding, please sand the lacquered surfaces before applying fresh lacquer and apply lacquer to the sanded surfaces as soon as possible. Woods with a very high wax content such as teak can have a negative effect on bonding in some circumstances. Water-soluble wood contents such as from ash and tannic acid from woods such as oak can initiate changes in colour tones and discolouration in the lacquer. For this reason we recommend a trial lacquering be undertaken as a matter of principle to assess the colour effect, bonding and drying progression under real conditions! Notes on cleaning and care: Please observe the care instructions in accordance with DIN 18356. Wipe parquet with a slightly damp, not wet, cloth. Please use only neutral, silicone-free, salmiac-free and non-abrasive cleaners. Regular care and cleaning with Hesse PROTECT-CLEANER PR 90 and Hesse INTENSIVE-CLEANER PR 91 increases the life of the sealing.

Parquet flooring, solid oak tiles
Wood sanding: grit/screen 100 with subsequent dedusting.
Sealing: 2 x 100 g/m² PURA-NATURA using suitable rollers.
Intermediate drying: at least 2 - 3 h / 20 °C room temperature and sufficient air circulation.
Intermediate sanding with single-disc sanding machine and sanding grid 120 - 150 and subsequent dedusting.
Accessible after drying for at least 8 h / 20 °C room temperature with sufficient air circulation. Fully accessible after at least 7 d / 20° C room temperature with sufficient air circulation.

Safety Data Sheets / Certificates

Material Safety Data Sheets

Contact

Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.