Hesse Hydro-PU-Color Lacquer HDB 5470x(gloss level)-(colour)

  • Good coverage and build
  • outstanding chemical and mechanical resistance
  • PVC-resistant, cream and sweat resistant and light fast.
Hesse HYDRO-PUR Color is a two-component colour lacquer with high opacity. This light fast multicoat lacquer for priming and top coating provides outstanding mechanical and chemical resistance. It is therefore also suitable for high-demand surfaces. The product is certified as flame retardant under DIN 4102 B1 and additionally classified under DIN EN 13501-1.
Request product Download data sheet
  • Description
  • Information on use
  • Sample process
  • Safety Data Sheets / Certificates

Fields of application

This product can be used for all interior fixtures, including heavily used areas such as the kitchen and bathroom. It can also be used on many different types of wood, as direct edge coating on MDF and on various foils. Best suited for coating heavily used components and also for staircases.

Technical specifications

Appearance opaque
Density series kg/l 1.048 - 1.212
Flow time 94 s / DIN 53211 - 4 mm
Form of delivery fluid
VOC EU % 3.71 %
Number of coats (max) 2
Amount per layer (minimum) 100 g/m²
Amount per layer (max) 150 g/m²
Total application volume 300 g/m²
Mixing ratio (by volume) 5 : 1 HYDRO Hardener HDR 5093
Mixing ratio (gravimetric) 100 : 17 HYDRO Hardener HDR 5093

Information on use

Usage time 2 h at 20 °C
Drying 16 h / 20 °C
Stackable after > 16 h / 20 °C
Complete drying 7 d / 20 °C
Surface preparation Clean, dry wood, clean suitable foil substrate or matching pigment filler. Free from oil, grease, wax and silicones. Correctly sanded and free from sanding dust.
Substrate sanding grits from-to 120 - 400
Intermediate sanding (grits) from-to 280 - 600
Finishing Subsequent coating: after sufficient drying and sanding back, if required, apply another coat of the same product or suitable HYDRO or PU products.
Comments on sanding The quality and uniformity of the wood / substrate and of the lacquer sanding are crucial to the final surface finish. After sanding, remove dust as prescribed.
Yield per coat 8 - 11 m²/l

The spreading rate is heavily dependent on the type of application. The specifications relate to a liter of ready-for-use product, if necessary including hardener and thinner.
Storage temperature 10 - 30 °C
Working temperature 20 °C
conditions of transport 10 - 30 °C
Processing instructions Add hardener slowly whilst stirring and adjust the spray viscosity by adding water or HYDRO Optimizer HZ 70, if required. Maximum additive volume 5 %. The hardener must always be added before thinning! The flow time should not be less than 40 s / DIN 4 mm after hardening and thinning. Never store product mixed with hardener in closed containers. Clean tools with water. For removal of dried lacquer residues use Hesse HYDRO Cleaning agent HV 6917. In case of combined coatings (HYDRO- and solvent based lacquers) rinse application tools with Hesse HYDRO Reversing agent HV 6904.
Particular instructions Pre-priming is possible depending on the required finish and carrier material, for instance using: HP 6645-9343, HDP 5640-9343, DP 4755-9343. Pre-prime exotic woods such as Macassar or extremely resinous knotty pine with PU sealing primer DG 4720-0001. When used on staircases (treads) we recommend finishing the colour lacquer surface with Hesse HYDRO-PUR PRIMO HDE 5400x(gloss level) or other Hesse HYDRO staircase lacquers.
General instructions on workmanship When working with HYDRO materials, parts that come into contact with the material must be made from stainless steel. The moisture content should be between 8 - 12 %. Do not apply or dry HYDRO lacquers at material or room temperatures below 18 °C. The ideal humidity for application lies between 55 and 65 %. During the lacquering process, a humidity level that is too low leads to surface defects (such as shrink cracks, etc.). Excessive humidity during the drying phase may drastically lengthen the drying time! In order to avoid adhesion problems, please sand the lacquered surfaces freshly before coating and apply lacquer to the sanded surfaces as soon as possible. When applied to foils, etc., please use a sample coating on the respective substrate to check the adhesion! The ideal complete hardening of lacquered surfaces that have been flashed off is reached at temperatures over 20 °C up to no more than 40 °C. Adequate, draft-free air exchange must be assured. The complete hardening of the lacquer will be reached after one week of proper storage (at least 20 °C room temperature). Woods containing large amounts of natural oils, such as teak, can negatively influence adhesion under certain circumstances. Water-soluble wood ingredients such those in ash and tannins in woods such as oak may cause colour changes and discolourations in the coating. We recommend that you always conduct a sample lacquering to evaluate the colour effect, adhesion and drying process under real conditions!

Vitrine in laminated MDF, white semi matt Sanding: 280 grit with subsequent dust removal. Basecoat: 1 - 2 x 180 - 200 g/m² Hesse 2C HYDRO Pigment filler HDP 5640-9343, mixing ratio (by volume) 7 : 1 with HYDRO Hardener HDR 5081. Drying: at least 16 h / 20 °C room temperature with adequate air circulation. Intermediate sanding: 280 grit with subsequent dust removal. Final sanding with HDB 54705-9010: 400 grit and subsequent dust removal. Coating: 1 - 2 x 120 - 150 g/m² Hesse HYDRO-PU Color HDB 54705-9010, mixing ratio (by volume) 5 : 1 with Hesse HYDRO Hardener HDR 5093. Intermediate drying: ideally 16 h / 20 °C with adequate air circulation. Intermediate sanding: 400 grit with subsequent dust removal. Stackable: after at least 24 h / 20 °C room temperature with adequate air circulation.

Contact

Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.