Hesse HYDRO-UV Multicoat lacquer DIACURO HUE 8608x(gloss level)

UV-curing HYDRO-UV multicoat lacquer for priming and top coating to achieve open- to closed-pore coatings on suitable substrates. This product satisfies the highest demands and is extremely resistant to scratches and chemical influences. The excellent chemical resistance of our HUE 86084 coating has been confirmed by a testing institute.
Request product Download data sheet
  • Description
  • Information on use
  • Sample process
  • Safety Data Sheets / Certificates

Fields of application

For all interior fittings, including in heavily used areas such as kitchen and bathroom. The special formulation of this lacquer also makes it suitable for coating wooden staircases to be creak-free.

Technical specifications

Yield per coat 8 - 13 m²/l

The spreading rate is heavily dependent on the type of application. The specified theoretic spreading rate reduces by up to 40 % with spray applications. Brushing or manual application methods are virtually loss-free. The specifications relate to a liter of ready-for-use product, if necessary including hardener and thinner.
Appearance colourless
Density series kg/l 1.037 - 1.061
Flow time 32 s / DIN 53211 - 6 mm
Form of delivery fluid
Non-volatile content series % 28 - 34.9
VOC EU % 2.58 %
Number of coats (max) 3
Amount per layer (minimum) 80 g/m²
Amount per layer (max) 130 g/m²
Total application volume 390 g/m²

Information on use

Stackable after Directly after UV curing and sufficient cooling.
Curing Hardening by means of ultraviolet rays with mercury UV-lamps. Sufficient radiation energy must be provided. This depends primarily on the type, conditions, age and design of the lamp system, so that the optimum UV lamp settings can be implemented on the respective system, and the curing should be checked. Your Hesse representative will assist you with the determination of the necessary radiant energy.
Mechanical drying Array
Surface preparation The substrate must be dry, dust-free and grease-free.
Substrate sanding grits from-to 150 - 240
Intermediate lacquer sanding (grits) from-to 280 - 400
Finishing Coat with products from the same series after drying and lacquer sanding.
Comments on sanding Sanded lacquer layers and surfaces must be coated directly.
Working temperature 20 °C
conditions of transport frost-free - up to a maximum of 35 °C
Processing instructions Working viscosity can be adjusted with water or HYDRO Optimizer HZ 70 (maximum 3 % by volume). For strip cleaning, we recommend the HYDRO Cleaner HY 6995 at a mixing ratio of 1 : 10 with water. Remove dried-on lacquer residues with special thinner ZD 82.
Particular instructions Always seal opened containers light-tight and air-tight to prevent skin forming. Remove dried lacquer residue using a sieve. Products in containers should be sieved before application.
General instructions on workmanship When applying HYDRO materials, parts that come into contact with the material must be made from non-rusting material. The wood moisture content should be between 8 and 12 %. Do not apply or dry HYDRO lacquers at material or room-temperatures below 18 °C. The ideal humidity for application lies between 55 and 65 %. During the lacquering process, a humidity level that is too low leads to shrink cracks; humidity that is too high hinders drying. In order to avoid adhesion problems, please sand the lacquered surfaces freshly before coating and apply lacquer to the sanded surfaces as soon as possible. When applied to foils, etc., please use a sample coating on the respective substrate to check the adhesion! If stored at least 20 °C, final hardness of the coating is achieved after a week. Woods with rich contents, such as teak, may have an adverse effect on adhesion. Water-soluble wood ingredients such those in ash and tannins in woods such as oak may cause colour changes and discolourations in the coating. Always conduct a sample lacquering to evaluate the colour effect, adhesion and drying process under real conditions.

The coating process and the precise treatment parameters are adapted in each case to the respective application and drying conditions and can be found in the customer-specific process descriptions (surface techniques).

Contact

Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.