Hesse PU Multicoat lacquer DE 51x(gloss level)

  • Universally applicable
  • light-fast
  • IMO certified
Two-component polyurethane acrylic resin lacquer, resilient, light-fast and formulated with additional light protection. A coating lacquer for priming and final lacquering. Universally applicable. This2129> product can be used on bleached wood. The French M1 standard (behaviour with fire) is also complied with.
So is
IMO certification. (flame-retardant coating for sea-going vessels)
Request product Download data sheet
  • Description
  • Information on use
  • Sample process
  • Safety Data Sheets / Certificates

Fields of application

This product can be used in restaurants, kitchens and bathrooms or for tables. It is suitable for surfaces requiring high resistance to chemical and mechanical stresses and is therefore ideal for heavily used surfaces. It can also be used on wenge, even if the bare wood is to be bleached and stained.

Technical specifications

Appearance colourless
Density series kg/l 0.919 - 0.932
Flow time (+/- 15 %) 30 s / DIN 53211 - 4 mm
Form of delivery fluid
Non-volatile content series % 23 - 25
Proportion of renewable raw materials % 0.2 - 0.5
VOC EU % 75.75 %
Number of coats (max) 3
Amount per layer (minimum) 100 g/m²
Amount per layer (max) 150 g/m²
Total application volume 450 g/m²
Mixing ratio (by volume) 10 : 1 PUR Hardener DR 472
Mixing ratio (gravimetric) 100 : 10 PUR Hardener DR 472

Information on use

Usage time 8 h / 20 °C
Pot life 3 d / 20 °C
Drying 2 h / 20 °C
Stackable after > 16 h / 20 °C
Complete drying 7 d / 20 °C
Surface preparation Clean, dry wood, dependent upon wood type and method of application
Substrate sanding grits from-to 150 - 180
Lacquer sanding (grit) from - to 280 - 320
Finishing Coat with products from the same series after drying and lacquer sanding.
Yield per coat 6 - 9 m²/l

The spreading rate is heavily dependent on the type of application. The specifications relate to a liter of ready-for-use product, if necessary including hardener and thinner.
Storage temperature 16 - 25 °C
Working temperature 20 °C
Processing instructions The maximum wet application amount when used as a low-flammable coating for seagoing vessels is 150 g/m². A lacquer/hardener mixture of 5 : 1 with PU Hardener DR 4072 is recommended for coating critical substrates. Hardening at 5 : 1 with PU Hardener DR 4076-0001 also enables direct coating of glass after adding 5 % Glass lacquer additive EL 460-0025 to the lacquer components. Please properly clean the glass surface using Cleaning thinner ZD 101 prior to application.
Particular instructions This product may only be combined with other approved and technically suitable products when it is used as a low-flammable coating for seagoing vessels according to the latest version of SOLAS 74/88 Reg. II-2/3, II-2/5 and II-2/6, IMO Resolution MSC.36(63)-(1994 HSC-Code) 7, IMO Resolution MSC.97(73)-(2000 HSC-Code) 7. The dull matt adjustment of this PU Multicoat lacquer means that it is only to be used as a 1-coat finish as opposed to a multi-layer lacquer coating! PU Multicoat lacquer DE 51x(gloss level) is ideally suited for finishing UNA-COLOR and provides outstanding ring-resistance. UNA-COLOR DB 45245-(colour tone) can be used to tint PU Multicoat lacquer DE 51x(gloss level), but only at a maximum addition of 10 %. A maximum of 5 % Colour concentrate ZD 1-(colour tone) can also be added to configure a glazing effect in PU Multicoat lacquer DE 51x(gloss level). Pre-priming is possible depending on the desired surface finish and substrate, for example using Basecoats DG 434, DG 417, DG 468-1 and DG 4763. “A risk assessment was undertaken according to Directive 2014/90/EU, Annex II, Section 3. This coating does not pose a physical risk to health nor a risk to the environment when cured and dried.”
General instructions on workmanship PU lacquers should not be applied or dried at material and room temperatures below 18 °C and 40 % RH, ideal values: 20 - 25 °C and 50 - 65 % RH. Deviations lead to problems with drying and/or curing. To avoid adhesion problems, please gently sand back the PU lacquered surfaces before applying fresh lacquer and apply lacquer to the sanded surfaces as soon as possible. Mixed residues from the previous day must only be used as a 10 - 20 % aggregate in a fresh lacquer/hardener mixture. Old lacquer/hardener mixtures impair the surface quality (adhesion/stability). Freshly bleached wood must be allowed at least 48 h intermediate drying / 20 °C before recoating with PU lacquers. The final hardness of the coating is achieved after one week in correct storage conditions (at least 20 °C room temperature).
Please conduct a sample coating under real conditions!

Hotel fixtures, low-flammable in accordance with M1, in natural oak, satin gloss and open-pored
Bare wood sanding: 150 - 180 grit (dust removal)
Basecoat: 1 x 120 g/m² PU Multicoat lacquer DE 516, mixing ratio (by volume) 10 : 1 with PU Hardener DR 4072
Intermediate drying: at least 2 h / 20 °C
Lacquer sanding: 280 -320 grit (dust removal)
Top coat: 1 x 120 g/m² PU Multicoat lacquer DE 516, mixing ratio (by volume) 10 : 1 with PU Hardener DR 4072
Packable: after at least 16 h / 20 °C

Material Safety Data Sheets

Contact

Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.