Hesse FANTASTIC-CLEAR DE 4877x(gloss level)

  • universally usable, even for heavily frequented areas
  • excellent adhesion properties, even on critical and bleached woods
  • easy application on vertical surfaces
FANTASTIC-CLEAR is a light fast , transparent and scratch-resistant acrylate-based multicoat lacquer. Its wide variety of application options and uncomplicated processing mean that FANTASTIC-CLEAR is superb as a multicoat lacquer on all common types of wood and in parallel as an excellent finishing lacquer on FANTASTIC-COLOR. Its excellent adhesion propertiesmean that FANTASTIC-CLEAR can also be used on bleached woods. Its good adhesion on vertical surfaces significantly reduces the risk of runs.
Request product Download data sheet
  • Description
  • Information on use
  • Sample process
  • Safety Data Sheets / Certificates

Fields of application

FANTASTIC-CLEAR can be used in all areas of interior design and shopfitting, including in kitchens and bathrooms. Hardening can be adapted to be object- or process-oriented. Detailed information can be found under “Application hints” in this Technical Information. FANTASTIC-CLEAR is ideally matched as a top coat to complement FANTASTIC-FILL and FANTASTIC-COLOR in a complete colour coating.

Technical specifications

Appearance colourless
Density series kg/l 0.92 - 0.926
Flow time (+/- 15 %) 30 s / DIN 53211 - 4 mm
Form of delivery fluid
Non-volatile content series % 23 - 25
Proportion of renewable raw materials % 0.3 - 0.5
VOC EU % 74.629997 %
Number of coats (max) 3
Amount per layer (minimum) 100 g/m²
Amount per layer (max) 150 g/m²
Total application volume 450 g/m²
Mixing ratio (by volume) 10 : 1 PU Hardener DR 4071
Mixing ratio (gravimetric) 100 : 10 PU Hardener DR 4071

Information on use

Usage time 8 h / 20 °C
Pot life 3 d / 20 °C
Drying 3 h / 20 °C
Stackable after > 16 h / 20 °C
Complete drying 7 d / 20 °C
Surface preparation Clean, dry wood, dependent upon wood type and method of application.
Substrate sanding grits from-to 150 - 400
Lacquer sanding (grit) from - to 280 - 400
Finishing After sufficient drying and immediately after interim sanding with lacquer from the same product range.
Yield per coat 6 - 9 m²/l

The spreading rate is heavily dependent on the type of application. The specifications relate to a liter of ready-for-use product, if necessary including hardener and thinner.
Processing instructions FANTASTIC-CLEAR can optionally be applied in a mixing ratio (by volume) of 5 : 1 with PU Hardener DR 4070. FANTASTIC-CLEAR dries to be slightly more glossy in this hardening. A more matt gloss level should be selected as necessary.
Hardening using PU Hardener DR 4076-0001 in a mixing ratio (by volume) of 5 : 1, after adding 5 % Glass lacquer additive EL 460-0025 to the lacquer components, enables direct coating on glass. The glass surface to be coated must first be properly cleaned using Cleaning thinner ZD 101.
This product must only be combined with other approved and technically suitable products when used as a flame retardant coating material for seagoing vessels according to the latest version of SOLAS 74/88 Reg. II-2/3, II-2/5 and II-2/6, IMO Resolution MSC.36(63)-(1994 HSC-Code) 7 and IMO Resolution MSC.97(73)-(2000 HSC-Code) 7. The maximum application amount in wet film when using this product as a flame retardant coating material for seagoing vessels is 240 g/m². This product is only suitable as a flame retardant coating for seagoing vessels when the default hardening is used, not the optional hardenings!
Particular instructions FANTASTIC-CLEAR DE 4877x(gloss level) should not be mixed with the FANTASTIC-CLEAR ULTRAMATT DE 48770-0 range! Mixing these two lacquer systems may result in incompatibility reactions or alterations in the respective product properties.
Colour lacquers UNA-COLOR DB 4524x(gloss level)-(colour tone) and FANTASTIC-COLOR DB 4888x(gloss level)-(colour tone) can be used as glazing lacquers to tint FANTASTIC-CLEAR DE 4877x(gloss level) (maximum addition 1.5 %). Depending on the substrate material and desired surface, the following Basecoats can be used in combination with FANTASTIC-CLEAR: DG 434 / DG 4734, DG 417 / DG 4717-0005, DG 468-1 / DG 4768-0011 and DG 4750.
FANTASTIC-CLEAR has been tested according to the standard test procedure of the American Society for Testing and Materials ASTM D7027-20 to determine its scratch resistance. The tested sample of DE 48770 did not show any scratches at a load of 700 g.
“A risk assessment was undertaken according to Directive 2014/90/EU, Annex II, Section 3. This coating does not pose a physical risk to health nor a risk to the environment when cured and dried.”
General instructions on workmanship PU lacquers should not be applied and dried at material and room-temperatures below 18 °C and 40 % RH. Ideal values are: 20 - 25 °C, 50 - 65 % RH. Deviations will result in drying or hardening errors. In order to avoid adhesion problems, please sand the PU lacquered surfaces before applying fresh lacquer and apply lacquer to the sanded surfaces as soon as possible. Old lacquer and hardener mixtures affect the surface quality (adhesion/resistance). Freshly bleached substrates must undergo intermediate drying for at least 48 h at 20 °C before coating with suitable PU lacquers. If stored correctly (at least 20 °C room temperature), the final hardness of the coating is achieved after a week.
Please apply a test coat under real conditions!

Natural beech heartwood sideboard for a conference room, matt
Wood sanding: 150 - 180 grit (dust removal)
Basecoat: 1 x 100 - 150 g/m² FANTASTIC-CLEAR DE 48772 at 20 °C room temperature, mixing ratio (by volume) 10 : 1 with PU Hardener DR 4071 and addition of 10 - 20 % Thinner DV 4900 to the lacquer/hardener mixture
Intermediate drying: 2.5 h / 20 °C
Lacquer sanding: 280 - 320 grit (dust removal)
Top coat: 1 x 100 - 150 g/m² FANTASTIC-CLEAR DE 48772 at 20 °C room temperature, mixing ratio (by volume) 10 : 1 with PU Hardener DR 4071 and addition of 10 - 20 % Thinner DV 4900 to the lacquer/hardener mixture
Packable: after at least 16 h / 20 °C

Safety Data Sheets / Certificates

Material Safety Data Sheets

Contact

Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.