Hesse RAPID-ISO-FILL DP 4764-9343

  • Isolation primer
  • fast-drying
  • Can be sanded to a powder
A pigmented two-component PU alkyd primer, fast drying and sands to a powder. Hesse RAPID- ISO-FILL DP DP 4764-9343 is a filling primer for coloured and closed-pore buildup of coloured lacquers.
Request product Download data sheet
  • Description
  • Information on use
  • Sample process
  • Safety Data Sheets / Certificates

Fields of application

For all interior fittings, including in kitchens, shop counters and bathrooms. Hesse RAPID-ISO-FILL can be applied to various types of wood, priming foil and as direct coating on MDF, including edges.

Technical specifications

Yield per coat 5 - 11 m²/l

The spreading rate is heavily dependent on the type of application. The specified theoretic spreading rate reduces by up to 40 % with spray applications. Brushing or manual application methods are virtually loss-free. The specifications relate to a liter of ready-for-use product, if necessary including hardener and thinner.
Appearance opaque
Density series kg/l 1.491
Flow time 68 s / DIN 53211 - 8 mm
Form of delivery fluid
Non-volatile content series % 70.5
VOC EU % 29.54 %
Number of coats (max) 4
Amount per layer (minimum) 140 g/m²
Amount per layer (max) 300 g/m²
Total application volume 800 g/m²
Mixing ratio (by volume) 2 : 1 PUR Hardener DR 4033
Mixing ratio (gravimetric) 100 : 31 PUR Hardener DR 4033

Information on use

Usage time 60 - 90 min / 20 °C
Pot life 70 min / 20 °C
Drying 3 h / 20 °C
Stackable after > 16 h / 20 °C
Complete drying 7 d / 20 °C
Surface preparation Clean, dry wood, depending on species and application method. Perform cleaning by sanding on foil or melamine before coating.
Substrate sanding grits from-to 150 - 320
Intermediate lacquer sanding (grits) from-to 320 - 400
Finishing After adequate drying and careful primer sanding with Hesse CN and PU coloured lacquers.
Working temperature 20 °C
Particular instructions As necessary, Hesse RAPID-ISO-FILL DP 4764-9343 can be hardened with Hesse PU Hardener DR 4036 to accelerate thorough drying. The open time when hardener is added is 30 minutes / 20 °C! In this paint/hardener combination, we recommend the use of two-component spraying equipment. For MDF substrates: With MDF coatings, you can avoid painting faults and edge breaks if you observe the following: Selection of an MDF quality suitable for the field of application, see manufacturer data on EU standard EN 622-5 pt.4 Test methods EN 317 (requirements on thickness swelling). Ideal panel moisture 5 - 7 %. If possible coat the MDF all around, the backs should at least receive a clear coating. Avoid sharp edges and milling grooves, round-off wherever possible. Coat edges and milling grooves 2 x with primer, do not sand through, if need be, prime again. Thick boards that have been built by gluing together several thinner boards are, due to the variance in tension, susceptible to edge ridging. It is better to select a single MDF board of the appropriate thickness. Panels that have been glued together should always be sanded flat at the edges and colourlessly pre-insulated. Any water introduced by the gluing process must be allowed to evaporate prior to coating. Store filler-coated surfaces in an air conditioned location and apply the final coat in a timely manner.
General instructions on workmanship PU lacquers should not be applied and dried at material and room-temperatures below 18 °C and 40 % RH. Ideal values are: 20 - 25 °C, 50 - 65 % RH. Deviations will result in drying or hardening errors. In order to avoid adhesion problems, please sand the PU lacquered surfaces before applying fresh lacquer and apply lacquer to the sanded surfaces as soon as possible. Old lacquer and hardener mixtures affect the surface quality (adhesion/resistance). Freshly bleached substrates must undergo intermediate drying for at least 48 h at 20 °C before coating with suitable PU lacquers. If stored correctly (at least 20 °C room temperature), the final hardness of the coating is achieved after a week.
Please apply a test coat under real conditions!

The coating process and the precise treatment parameters are adapted in each case to the respective application and drying conditions and can be found in the customer-specific process descriptions (surface techniques).

Material Safety Data Sheets

Contact

Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.