Fields of application
EASY-FILL can be used for shopfitting and all interior fittings, including those in kitchens and bathrooms. We recommend PU Isolation primer DP 4791-9343 for professional use beneath high gloss.
Technical specifications
Appearance |
opaque
|
Density series kg/l |
1.423
|
Flow time (+/- 15 %) |
30 s / DIN 53211 - 6 mm
|
Form of delivery |
fluid
|
Non-volatile content series % |
65
|
VOC EU % |
34.84 %
|
Number of coats (max) |
4
|
Amount per layer (minimum) |
140 g/m²
|
Amount per layer (max) |
300 g/m²
|
Total application volume |
500 g/m²
|
Mixing ratio (by volume) |
100 : 15 PUR Hardener DR 4096-0002
|
Mixing ratio (gravimetric) |
100 : 10 PUR Hardener DR 4096-0002
|
Information on use
Usage time |
3.0 - 3.5 h / 20 °C
|
Drying |
3 h / 20 °C
|
Stackable after |
> 16 h / 20 °C
|
Complete drying |
7 d / 20 °C
|
Surface preparation |
Clean, dry wood, depending on species and application method. Perform cleaning by sanding on foil or melamine before coating.
|
Substrate sanding grits from-to |
150 - 320
|
Lacquer sanding (grit) from - to |
320 - 400
|
Finishing |
After adequate drying and careful primer sanding with Hesse CN and PU coloured lacquers.
|
Comments on sanding |
In case of direct coating on cleaned and sanded foils, please make a test coating to check the adhesion!
|
Yield per coat |
5 - 10 m²/l
The spreading rate is heavily dependent on the type of application. The specifications relate to a liter of ready-for-use product, if necessary including hardener and thinner.
|
Storage temperature |
16 - 40 °C
|
Working temperature |
20 °C
|
Processing instructions |
Application of between one and four coats at 100 - 300 g/m² on suitable substrates. The maximum application amount in wet film is 500 g/m².
|
Particular instructions |
Any addition of thinner in relation to the lacquer/hardener mixture is subject to various factors and has to be individually adapted to the component being coated as well as to the climatic and mechanical conditions. In the case of FANTASTIC-FILL, an addition of 0 - 30 % is possible. A mixing ratio (by weight) of 10 : 1 or a mixing ratio (by volume) of 100 : 15 equates to a mixing ratio (by volume) of 7 : 1 given the graduation on commercial mixing jugs. This product must only be combined with other approved and technically suitable products when used as a flame retardant coating material for seagoing vessels according to the latest version of SOLAS 74/88 Reg. II-2/3, II-2/5 and II-2/6, IMO Resolution MSC.36(63)-(1994 HSC-Code) 7 and IMO Resolution MSC.97(73)-(2000 HSC-Code) 7. The maximum application amount in wet film when using this product as a flame retardant coating material for seagoing vessels is 140 g/m². “A risk assessment was undertaken according to Directive 2014/90/EU, Annex II, Section 3. This coating does not pose a physical risk to health nor a risk to the environment when cured and dried.”
|
General instructions on workmanship |
PU lacquers should not be applied or dried at material and room temperatures of less than 18 °C and 40 % RH, ideal values: 20 - 25 °C, 50 - 65 % RH. Deviations will result in drying or curing faults. To avoid adhesion problems, please sand PU lacquered surfaces before applying fresh lacquer and apply lacquer to these sanded surfaces as soon as possible. Old lacquer/hardener mixtures will affect the surface quality (adhesion/resistance). If stored correctly (at least 20 °C room temperature), complete hardening of the coating is achieved after a week. Please apply a test coat under real conditions! On MDF substrates: Thick boards that have been created by gluing together several thinner boards are, due to the variance in tension, susceptible to edge ridging. It is better to select a single MDF board of the appropriate thickness. Panels that have been glued together should always be sanded flat at the edges and colourlessly pre-insulated. Any water introduced by gluing must be allowed to evaporate prior to coating.
|
MDF cabinet front in RAL 9016, matt
Surface sanding: 320 - 400 grit (dust removal)
Edge and profile sanding: 150 - 180 grit (dust removal)
Basecoat: 1 x 150 - 200 g/m² Hesse EASY-FILL DP 4788-9343, mixing ratio (by volume) 100 : 15 with PU Hardener DR 4096-0002 and the addition of 10 % Thinner DV 4900 to the lacquer/hardener mixture
Drying: at least 3 h / 20 °C, preferably 16 h / 20 °C
Filler sanding: 320 - 400 grit (dust removal)
Basecoat: 1 x 150 - 200 g/m² Hesse EASY-FILL DP 4788-9343, mixing ratio (by volume) 100 : 15 with PU Hardener DR 4096-0002 and the addition of 10 % Thinner DV 4900 to the lacquer/hardener mixture
Drying: at least 5 h / 20 °C, preferably 16 h / 20 °C
Filler sanding: 320 - 400 grit (dust removal)
Colour lacquering: 1 x 120 - 150 g/m² Hesse UNA-COLOR DB 45245-9016, mixing ratio (by volume) 10 : 1 with PU Hardener DR 4070 and the addition of 10 - 20 % Thinner DV 4900 to the lacquer/hardener mixture
Drying: at least 5 h / 20 °C
Lacquer sanding / smoothing: 400 grit (dust removal)
Final coating: 1 x 80 - 100 g/m² Hesse UNA-PUR DE 42592, mixing ratio (by volume) 10 : 1 with PU Hardener DR 4070 and the addition of 10 - 20 % Thinner DV 4900 to the lacquer/hardener mixture
Complete drying: at least 16 h / 20 °C
Material Safety Data Sheets
Contact
Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always
available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge
available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our
terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.