Fields of application
FANTASTC-FILL DP 4755-9005 can be used in all areas of interior design and shopfitting, including in kitchens, bathrooms and the fitting out of ship interiors. After matt sanding, it can also be used without hesitation on the widest variety of wood types, MDF and many laminates. Its excellent adhesion properties mean that this PU Isolating filler can additionally be used as an adhesion primer on various plastics.
Technical specifications
Appearance |
opaque
|
Density series kg/l |
1.399
|
Flow time (+/- 15 %) |
66 s / DIN 53211 - 6 mm
|
Form of delivery |
fluid
|
Non-volatile content series % |
63
|
Proportion of renewable raw materials % |
0.4
|
VOC EU % |
36.849998 %
|
Number of coats (max) |
3
|
Amount per layer (minimum) |
140 g/m²
|
Amount per layer (max) |
300 g/m²
|
Total application volume |
550 g/m²
|
Mixing ratio (by volume) |
10 : 1 PU Hardener DR 4071
|
Mixing ratio (gravimetric) |
100 : 7 PU Hardener DR 4071
|
Information on use
Usage time |
> 8 h / 20 °C
|
Pot life |
6 h / 20 °C
|
Drying |
3 h / 20 °C
|
Complete drying |
7 d / 20 °C
|
Surface preparation |
Clean, dry wood, depending on species and application method. Perform cleaning by sanding on foil or melamine before coating.
|
Substrate sanding grits from-to |
150 - 320
|
Lacquer sanding (grit) from - to |
320 - 400
|
Finishing |
FANTASTIC-FILL DP 4755-9005 can be recoated after adequate drying and the specified sanding using the following Hesse colour series: DB 555-(colour tone), DB 4524x(gloss level)-(colour tone) / DB 525-(colour tone), DB 4520x(gloss level)-(colour tone), DB 4476x(gloss level)-(colour tone), DB 4888x(gloss level)-(colour tone). FANTASTIC-FILL can also be used beneath high gloss lacquers in the Hesse colour series DB 449-(colour tone) and DB 44099-(colour tone). Although Hesse PU Isolating filler DP 491-9343 / DP 4791-9343 would be the first choice for the best results beneath high gloss. Moreover, after prior review of the results, it is also possible to apply a top coat using most common coloured paints.
|
Comments on sanding |
In case of direct coating on cleaned and sanded foils, please make a test coating to check the adhesion! Sanding with 400 - 600 grit is recommended before applying a final coat of high gloss finish.
|
Yield per coat |
5 - 10 m²/l
The spreading rate is heavily dependent on the type of application. The specifications relate to a liter of ready-for-use product, if necessary including hardener and thinner.
|
Storage temperature |
16 - 40 °C
|
Working temperature |
20 °C
|
Particular instructions |
FANTASTIC-FILL can universally be used with the properties of an isolating filler in a mixing ratio (by volume) of 10 : 1 with PU Hardener DR 471 / DR 4071. In this hardening ratio FANTASTIC-FILL can in parallel be used on the following sanded metals from which grease has been removed: iron, galvanized iron, V2A sheet metals and aluminium. Conduct a trial coating as necessary. FANTASTIC-FILL is Decopaint-compliant in a mixing ratio (by volume) of 3 : 1 with PU Hardener DR 4076-0001 without the addition of thinner. It also meets the requirements of ChemVOC FarbV.
On MDF substrates: Thick boards that have been created by gluing together several thinner boards are, due to the variance in tension, susceptible to edge ridging. It is better to select a single MDF board of the appropriate thickness. Panels that have been glued together should always be sanded flat at the edges and colourlessly pre-insulated. Any water introduced by gluing must be allowed to evaporate prior to coating.
This product must only be combined with other approved and technically suitable products when used as a flame retardant coating material for seagoing vessels according to the latest version of SOLAS 74/88 Reg. II-2/3, II-2/5 and II-2/6, IMO Resolution MSC.36(63)-(1994 HSC-Code) 7 and IMO Resolution MSC.97(73)-(2000 HSC-Code) 7. The maximum application amount in wet film when using this product as a flame retardant coating material for seagoing vessels is 150 g/m². “A risk assessment was undertaken according to Directive 2014/90/EU, Annex II, Section 3. This coating does not pose a physical risk to health nor a risk to the environment when cured and dried.”
|
General instructions on workmanship |
PU lacquers should not be applied or dried at material and room temperatures of less than 18 °C and 40 % RH, ideal values: 20 - 25 °C, 50 - 65 % RH. Deviations will result in drying or curing faults. To avoid adhesion problems, please sand PU lacquered surfaces before applying fresh lacquer and apply lacquer to these sanded surfaces as soon as possible. Old lacquer/hardener mixtures will affect the surface quality (adhesion/resistance). If stored correctly (at least 20 °C room temperature), complete hardening of the coating is achieved after a week. Please apply a test coat under real conditions!
|
Laminated MDF cabinet fronts in RAL 9005, matt
Surface sanding: 320 - 400 grit (dust removal)
Edge and profile sanding: 150 - 180 grit (dust removal)
Basecoat: 1 x 150 - 200 g/m² Hesse FANTASTIC-FILL DP 4755-9005, mixing ratio (by volume) 10 : 1 with PU Hardener DR 4071 / DV 471 and addition of 15 % Thinner DV 4900 / DV 490 to the lacquer/hardener mixture
Drying: > 2 h / 20 °C, preferably 16 h / 20 °C
Filler sanding: 320 - 400 grit (dust removal)
Basecoat: 1 x 150 - 200 g/m² Hesse FANTASTIC-FILL DP 4755-9005, mixing ratio (by volume) 10 : 1 with PU Hardener DR 4071 / DV 471 and addition of 15 % Thinner DV 4900 / DV 490 to the lacquer/hardener mixture
Drying: > 2 h / 20 °C, preferably 16 h / 20 °C
Filler sanding: 320 - 400 grit (dust removal)
Colour and top coat: 1 x 120 - 180 g/m² Hesse FANTASTIC-COLOR DB 48882-9005, mixing ratio (by volume) 10 : 1 with PU Hardener DR 4071 / DR 471 and addition of 10 - 30 % Thinner DV 4900 / DV 490 to the lacquer/hardener mixture
Complete drying: > 16 h / 20 °C
Safety Data Sheets / Certificates
Material Safety Data Sheets
Contact
Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always
available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge
available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our
terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.