Fields of application
DG 45205-(colour tone) can also be used for shopfitting and all interior fixtures and fittings, including in kitchens and bathrooms as well as the fitting out of ship interiors. Aside from that, the product can be used with different types of hardeners and mixing ratios
Technical specifications
Appearance |
opaque
|
Density series kg/l |
0.982 - 1.107
|
Flow time (+/- 15 %) |
45 s / DIN 53211 - 4 mm
|
Form of delivery |
fluid
|
Proportion of renewable raw materials % |
0 - 0.4613976
|
VOC EU % |
68.379997 %
|
Number of coats (max) |
2
|
Amount per layer (minimum) |
80 g/m²
|
Amount per layer (max) |
150 g/m²
|
Total application volume |
300 g/m²
|
Mixing ratio (by volume) |
10 : 1 PU Hardener DR 4070
|
Mixing ratio (gravimetric) |
100 : 9 PU Hardener DR 4070
|
Information on use
Usage time |
8 h / 20 °C
|
Pot life |
3 d / 20 °C
|
Drying |
3 h / 20 °C
|
Stackable after |
> 16 h / 20 °C
|
Complete drying |
7 d / 20 °C
|
Surface preparation |
Perform cleaning by sanding on foil or melamine before coating.
|
Substrate sanding grits from-to |
150 - 320
|
Lacquer sanding (grit) from - to |
320 - 400
|
Finishing |
With another coat of the same. Please use the likes of MEGA-PUR DE 4503x(gloss level) or DE 4259x(gloss level) for top coating if complete ring and abrasion resistance or a different gloss level are required.
|
Comments on sanding |
When directly coating cleaned or sanded foils, please apply a test coat to check the bonding. When applying a final coat of Hesse PU Coloured lacquer DB 45205-(colour tone) with high gloss, intermediate lacquer sanding with grit 600 - 800 is recommended.
|
Yield per coat |
7 - 13 m²/l
The spreading rate is heavily dependent on the type of application. The specifications relate to a liter of ready-for-use product, if necessary including hardener and thinner.
|
Storage temperature |
16 - 40 °C
|
Working temperature |
20 °C
|
Processing instructions |
The maximum total application amount when being used as a flame-retardant coating agent for seagoing vessels is 130 g/m². When directly coating cleaned or sanded foils, please apply a test coat to check the bonding. For particular strains on the surface and on critical carriers, harden with DR 4070 to the ratio of 5 : 1. A hardening additive ratio of 10 : 1 with DR 4071 is necessary for direct coatings onto MDF. A hardening additive ratio of 10 : 1 can accelerate complete drying (pay attention to shorter potlife here). The hardening additive ratio of 5 : 1 with DR 4076-0001 following prior mixture of 5 % Glass lacquer additive EL 460-0025 to lacquer products also makes it possible to apply the lacquer directly onto glass following prior cleaning in accordance with regulations.
|
Particular instructions |
This product may only be combined with other approved and technically suitable products when it is used as a flame-retardant coating material for seagoing vessels according to the latest version of SOLAS 74/88 Regulations II-2/3, II-2/5 and II-2/6, IMO Resolution MSC.36(63)-(1994 HSC-Code) 7 and IMO Resolution MSC.97(73)-(2000 HSC-Code) 7. Pre-priming is possible depending on the required finish and substrate material, for instance using DP 4755-9343 and DP 4791-9343., We would recommend using Hesse MEGA-PUR DE 4503x(gloss level) or Hesse UNA-PUR DE 4259x(gloss level) for the top coat if absolute metal-marking and abrasion resistance or a different gloss level are required. “A risk assessment was undertaken according to Directive 2014/90/EU, Annex II, Section 3. This coating does not pose a physical risk to health nor a risk to the environment when cured and dried.”
|
General instructions on workmanship |
PU lacquers should not be applied and dried at material and room-temperatures below 18 °C and 40 % RH. Ideal values are: 20 - 25 °C, 50 - 65 % RH. Deviations will result in drying or hardening errors. In order to avoid adhesion problems, please sand the PU lacquered surfaces before applying fresh lacquer and apply lacquer to the sanded surfaces as soon as possible. Old lacquer and hardener mixtures affect the surface quality (adhesion/resistance). Freshly bleached substrates must undergo intermediate drying for at least 48 h at 20 °C before coating with suitable PU lacquers. If stored correctly (at least 20 °C room temperature), the final hardness of the coating is achieved after a week. Please apply a test coat under real conditions!
|
Doctor's practice, open-pored ash with wetted pores, semi matt finish.
Wood sanding: 150 grit (dust removal)
Basecoat: 1 x Hesse UNA-THIX-COLOR DB 45205-9010 with so full a coating that the pores appear closed when wet (200 - 300 g/m²), mixing ratio (by volume) 10 : 1 with PU Hardener DR 4070 and the addition of 30 - 40 % Thinner DV 4900.
Drying: at least 16 h / 20 °C
Lacquer sanding: 320 grit)
Coating: 1 x 100 - 150 g/m² Hesse UNA-THIX-COLOR DB 45205-9010, mixing ratio (by volume) 10 : 1 with PU Hardener DR 4070 and the addition of 20 - 30 % Thinner DV 4900. Allow 1 - 2 h / 20 °C and, without lacquer sanding, apply a top coat of 80 - 100 g/m² Hesse MEGA-PUR DE 45034, mixing ratio (by volume) 10 : 1 with PU Hardener DR 4070 and the addition of 10 % Thinner DV 4900.
Complete drying: at least 16 h / 20 °C
Safety Data Sheets / Certificates
Material Safety Data Sheets
Contact
Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always
available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge
available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our
terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.