Hesse PU Metallic DB 4263x(gloss level)-(colour tone)

  • uniform colour effect
  • light fast
  • fast drying and aromatic-free
Two-component PU acrylate colour lacquer, pigmented, light-fast, opaque, fast-drying and with a uniform colour effect. For effect coatings from open- to closed-pore surface processes. Available in many colours.
Request product Download data sheet
  • Description
  • Information on use
  • Sample process
  • Safety Data Sheets / Certificates

Fields of application

For decorative interiors, hotel facilities and furniture surfaces on appropriate PU primers.

Technical specifications

Yield per coat 8 - 12 m²/l

The spreading rate is heavily dependent on the type of application. The specified theoretic spreading rate reduces by up to 40 % with spray applications. Brushing or manual application methods are virtually loss-free. The specifications relate to a liter of ready-for-use product, if necessary including hardener and thinner.
Appearance opaque
Density series kg/l 0.897 - 1.066
Flow time 44 s / DIN 53211 - 4 mm
Form of delivery fluid
Non-volatile content series % 7.5 - 35.5
VOC EU % 76.63 %
Number of coats (max) 1
Amount per layer (minimum) 80 g/m²
Amount per layer (max) 120 g/m²
Total application volume 120 g/m²
Mixing ratio (by volume) 10 : 1 PU Hardener DR 4070
Mixing ratio (gravimetric) 100 : 10 PU Hardener DR 4070

Information on use

Usage time 8 h / 20 °C
Pot life 1 d / 20 °C
Drying 3 h / 20 °C
Stackable after > 16 h / 20 °C
Complete drying 7 d / 20 °C
Surface preparation

Use clean, dry wood depending on the type of wood, application method and desired effect. Perform cleaning by sanding on foil or melamine before coating.

Substrate sanding grits from-to 150 - 320
Intermediate lacquer sanding (grits) from-to 320 - 400
Finishing Depending on the desired effect, with appropriate light-fast Hesse PU multicoat, finishing and brilliant lacquers. The overpainting influences the colour tone to a greater or lesser degree depending on the colouring.
Working temperature 20 °C
Processing instructions The spray nozzle size, air pressure and addition of thinner will influence the effect! Hardening at 5 : 1 with PU Hardener DR 4076-0001 after previously mixing in 5 % Hesse Glass lacquer additive EL 460-0025 to the lacquer component also enables direct application of the lacquer onto glass after proper cleaning.
Particular instructions Metallic lacquers have to be applied evenly. The application quantities, application methods and drying conditions influence the colour tone and effect. Pre-priming is possible, depending on the desired surface and the substrate, e.g. using Hesse PU Isolating filler DP 4791-9343, FANTASTIC-FILL DP 4755-9343 or PU Colour lacquer DB 45245-(colour tone). To achieve optimal chemical and mechanical resistance and obtain a customized gloss level, the metallic lacquer can also be recoated after 4 - 6 h / 20 °C without lacquer sanding, e.g. using DE 4259x(gloss level), DE 4503x(gloss level), DU 45540 or DU 45229.
This product must only be combined with other approved and technically suitable products when used as a flame retardant coating material for seagoing vessels according to the latest version of SOLAS 74/88 Reg. II-2/3, II-2/5 and II-2/6, IMO Resolution MSC.36(63)-(1994 HSC-Code) 7 and IMO Resolution MSC.97(73)-(2000 HSC-Code) 7. The maximum application amount in wet film when using this product as a flame retardant coating material for seagoing vessels is 120 g/m². “A risk assessment was undertaken according to Directive 2014/90/EU, Annex II, Section 3. This coating does not pose a physical risk to health nor a risk to the environment when cured and dried.”
General instructions on workmanship PU lacquers should not be used or dried at material and room temperatures of less than 18 °C and 40 % RH, ideal values: 20 - 25 °C, 50 - 65 % RH. Deviations will result in drying or curing errors. In order to avoid adhesion problems, please sand the PU lacquered surfaces before applying fresh lacquer and apply lacquer to the sanded surfaces as soon as possible. If stored correctly (at least 20 °C room temperature), complete hardening of the coating is achieved after a week. Freshly bleached woods must undergo intermediate drying for at least 48 h / 20 °C before overpainting with PU lacquers. Please test the lacquer under real conditions!

Object constructed in MDF (veneer, filled) metallic
Sanding: 400 - 600 grit
Coating: 1 x 80 - 120 g/m² Hesse PU Metallic DB 42634-M0133, mixing ratio (by volume) 10 : 1 with PU Hardener DR 4070, thinned 30 - 40 % using DV 4900
Intermediate drying: 2 - 3 h / 20 °C
Top coat: 1 x 80 - 120 g/m² Hesse PU Multi-coat lacquer DE 42597, mixing ratio (by volume) 10 : 1 with PU Hardener DR 4070, thinned 10 % using DV 4900
Packable: after drying for at least 16 h / 20 °C

Contact

Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.