Hesse UV Basecoat UG 7347

  • good sanding properties with good transparency
  • ideal as a coat for corundum basecoats for open- to closed pore coatings
The product UG 7347 is a sanding sealer, which is used as the final basecoat in the system configuration before the sanding machine is used. The basecoat is therefore ideal for preparing the subsequent top coats for sanding. This UV activated product is especially used for corundum basecoats, such as UG 7465.
Request product Download data sheet
  • Description
  • Information on use
  • Sample process
  • Safety Data Sheets / Certificates

Fields of application

System configuration as basecoat for resistant real wood surfaces in the parquet industry. For open- to closed-pore substrates

Technical specifications

Appearance colourless
Density series kg/l 1.262
Flow time (+/- 15 %) 38 s / DIN 53211 - 8 mm
Form of delivery fluid
Non-volatile content series % 99.7
VOC EU % 0.24 %
Number of coats (max) 3
Amount per layer (minimum) 10 g/m²
Amount per layer (max) 30 g/m²
Total application volume 80 g/m²

Information on use

Stackable after stackable directly after UV curing
Curing Hardening by means of ultraviolet rays with mercury UV-lamps.Sufficient radiation energy must be provided. This depends primarily on the type, conditions, age and design of the lamp system, so that the optimum UV lamp settings can be implemented on the respective system, and the curing should be checked. Your Hesse representative will assist you with the determination of the necessary radiant energy.
Surface preparation gelled or sanded UV basecoats.
Substrate sanding grits from-to 150 - 180
Lacquer sanding (grit) from - to 280 - 320
Finishing For system build-up with certified products such as suitable UV lacquers.
Comments on sanding Sanding is required to achieve good adhesion to the substrate depending on the substrate’s condition. Wood substrates should be sanded at 120 - 220 grit subject to wood type. Membrane substrates and basecoats should be freshly sanded at 320 - 600 grit. Dust should be carefully removed from the substrate after sanding. Intermediate sanding should generally be omitted when the bond is established when using a primer or the gelling process.
Yield per coat 42 - 126 m²/l

The spreading rate is heavily dependent on the type of application. The specifications relate to a liter of ready-for-use product, if necessary including hardener and thinner.
Storage temperature 5 - 25 °C
conditions of transport frost-free - up to a maximum of 35 °C
Processing instructions Regularly check the specified application quantities. Clean rollers using suitable thinners!
General instructions on workmanship Clean lamps and reflectors on a regular basis using a soft, lint-free cloth and UV 7111.
Only touch the lamps when wearing cotton gloves. Note the lamp's operating hours and replace them as per the lamp manufacturer's recommendations. Always protect open containers from the incidence of light (cover them).
Seal containers properly after use.
Sufficient lacquer sanding and inspection of the bond within the entire structure will be required in each case. Please apply a trial coating under practical conditions!

Closed-pore parquet configuration on maple, dull matt, examination according to S-42
Base wood sanding: graduated to 120 (dust removal)
Adhesion primer: 1 x 10 - 12 g/m² Hesse HYDRO-UV Basecoat for roller coating HUW 8831
Intermediate drying in ambient air or UV activation
Light putty: 1 x 20 - 30 g/m² Hesse UV Putty UG 7230-0001 colourless
Gelling
Basecoat: 1 x 20 - 25 g/m² Hesse UV Basecoat for roller coating UG 7465 colourless
Gelling
Basecoat: 1 x 20 - 25 g/m² Hesse UV Basecoat for roller coating UG 7465 colourless
Gelling
Basecoat: 1 x 20 - 25 g/m² Hesse UV Basecoat for roller coating UG 7465 colourless
UV activation
Lacquer sanding: grain 400
Top coat: 1 x 5 - 7 g/m² Hesse UV Basecoat for roller coating top coat UU 74501 colourless
Gelling
Top coat: 1 x 5 - 7 g/m² Hesse UV Basecoat for roller coating top coat UU 74501 colourless
UV activation

Material Safety Data Sheets

Contact

Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.