Hesse HYDRO-PU Natural Wood effect HDE 54500-0001

  • With light protection
  • Natural wood effect
  • Dull matt with good scratch resistance
Our colourless HYDRO-PU multicoat lacquer creates an attractive, dull matt, natural wood effect combined with good scratch resistance and surface durability. Using this light fast 2C natural wood effect lacquer results in the special natural wood effect being retained for a very long time. This product is suitable for priming and top coating open pored surfaces.
Request product Download data sheet
  • Description
  • Information on use
  • Sample process
  • Safety Data Sheets / Certificates

Fields of application

For all interior fittings in living areas, with a natural wood effect; predominantly on light woods. Also for stairs and handrails. Can also be used on bleached surfaces (that are adequately dry).

Technical specifications

Appearance colourless
Decopaint basis WB
Decopaint category J
Density series kg/l 1.023
Flow time (+/- 15 %) 60 s / DIN 53211 - 4 mm
Form of delivery fluid
Non-volatile content series % 22
Profile of properties Brightening
VOC EU % 5.9 %
Number of coats (max) 2
Amount per layer (minimum) 80 g/m²
Amount per layer (max) 100 g/m²
Total application volume 200 g/m²
Mixing ratio (by volume) 10 : 1 HYDRO Hardener HDR 5081
Mixing ratio (gravimetric) 100 : 10 HYDRO Hardener HDR 5081

Information on use

Usage time 2 h / 20 °C
Pot life 2 h / 20 °C
Drying 3 h / 20 °C
Stackable after > 16 h / 20 °C
Complete drying 7 d / 20 °C
Surface preparation Clean, dry wood, free of oil, grease, wax and silicones. Sanded as prescribed and free from sanding dust.
Substrate sanding grits from-to 120 - 220
Lacquer sanding (grit) from - to 280 - 320
Finishing After suitable drying can be recoated with the same product.
Comments on sanding The quality and uniformity of the wood / substrate and of the lacquer sanding are crucial to the final surface finish. After sanding, remove dust as prescribed.
Yield per coat 10 - 13 m²/l

The spreading rate is heavily dependent on the type of application. The specifications relate to a liter of ready-for-use product, if necessary including hardener and thinner.
Working Temperature Range 18 - 22 °C
Storage temperature 10 - 30 °C
Working temperature 20 °C
conditions of transport 10 - 30 °C
Processing instructions Add hardener slowly whilst stirring. Adjust the spray viscosity with water if required. Maximum additive volume 5 %. The hardener must always be added before thinning! Never store product mixed with hardener in closed containers. Over-paintability: possible with another coat of the same product or with suitable colourless materials. Clean tools with water. For removal of dried lacquer residues use Hesse HYDRO Cleaning agent HV 6917. In case of combined coatings (HYDRO- and solvent based lacquers) rinse application tools with Hesse HYDRO Reversing agent HV 6904.
Particular instructions The product can be used on surfaces that have been bleached with hydrogen peroxide and thoroughly dried. Pre-priming on tanning-rich woods such as oak with HDG 5410. Beware! Do not sand through the basecoat as there is a risk of staining.
General instructions on workmanship When working with HYDRO materials, parts that come into contact with the material must be made from stainless steel. The moisture content should be between 8 - 12 %. Do not apply or dry HYDRO lacquers at material or room temperatures below 18 °C. The ideal humidity for application lies between 55 and 65 %. During the lacquering process, a humidity level that is too low leads to surface defects (such as shrink cracks, etc.). Excessive humidity during the drying phase may drastically lengthen the drying time! In order to avoid adhesion problems, please sand the lacquered surfaces freshly before coating and apply lacquer to the sanded surfaces as soon as possible. When applied to foils, etc., please use a sample coating on the respective substrate to check the adhesion! The ideal complete hardening of lacquered surfaces that have been flashed off is reached at temperatures over 20 °C up to no more than 40 °C. Adequate, draft-free air exchange must be assured. The complete hardening of the lacquer will be reached after one week of proper storage (at least 20 °C room temperature). Woods containing large amounts of natural oils, such as teak, can negatively influence adhesion under certain circumstances. Water-soluble wood ingredients such those in ash and tannins in woods such as oak may cause colour changes and discolourations in the coating. We recommend that you always conduct a sample lacquering to evaluate the colour effect, adhesion and drying process under real conditions!

Commercial furnishings, natural oak-wood effect Wood-sanding grit 120 - 150 with subsequent dust removal. Basecoat: 1 - 2 x 80 - 120 g/m² Hesse HYDRO-PU natural wood primer HDG 5410, mixing ratio (by volume) 10 : 1 with Hardener HDR 5081. Intermediate drying: at least 2 h / 20 °C room temperature with sufficient air circulation. Smoothing: grit 400 with subsequent dust removal. Top coating: 1 x 100 - 120 g/m² Hesse HYDRO-PU Natural Wood-Effect HDE 54500-0001, mixing ratio (by volume) 10 : 1 with Hardener HDR 5081. Packable: after drying for at least 16 h / 20 °C room temperature and sufficient air circulation.

Material Safety Data Sheets

Contact

Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.