Hesse 2C HYDRO Filler HDP 5640-9343

  • Good body
  • Thixotropic
  • universally usable
  • IMO-approved
Pigment filler HDP 5640-9343 is an IMO-certified 2C primer with a broad field of application and is especially suitable for highly durable surfaces, such as those in wet rooms. Its filling power and thixotropy make this HYDRO-acrylate product especially easy to use. Our Hesse 2C HYDRO Pigment filler can be machine sanded and can subsequently be coated with all suitable Hesse lacquer systems. The product is certified as flame retardant to DIN 4102 B1 and additionally classified under DIN EN 13501-1.
Request product Download data sheet
  • Description
  • Information on use
  • Sample process
  • Safety Data Sheets / Certificates

Fields of application

For all interior designs, ideal for heavily used surfaces such as in kitchens, bathrooms and offices. And throughout residential settings, for instance for tables and sideboards; on a wide selection of wood species, on plywood, MDF, and on the edges of MDF. Also for stairs and handrails.

Technical specifications

Appearance opaque
Decopaint basis WB
Decopaint category J
Density series kg/l 1.379
Flow time (+/- 15 %) 75 s / DIN 53211 - 4 mm
Form of delivery fluid
Non-volatile content series % 59.7
VOC EU % 2.66 %
Number of coats (max) 3
Amount per layer (minimum) 100 g/m²
Amount per layer (max) 180 g/m²
Total application volume 450 g/m²
Mixing ratio (by volume) 7 : 1 HYDRO Hardener HDR 5081
Mixing ratio (gravimetric) 100 : 10 HYDRO Hardener HDR 5081

Information on use

Usage time 2 h / 20 °C
Pot life 2 h / 20 °C
Drying 5 h / 20 °C
Stackable after > 16 h / 20 °C
Complete drying 7 d / 20 °C
Surface preparation Clean, well-seasoned wood, or clean, suitable MDF or plywood base, free from oil, grease, wax and silicones. Sanded as prescribed and free from sanding dust. Depending on the kind of wood and the desired surface effect: graduated raw wood sanding with grit size 120 - 220 and subsequent dedusting. The quality of the wood sanding is a decisive factor for the quality of the final surface. For foil substrates: suitable foil: sanding with grit size 320 - 400 and subsequent dedusting and degreasing, if necessary. The foil quality and the quality of the foil sanding are decisive factors for the quality of the final surface.
Substrate sanding grits from-to 120 - 400
Lacquer sanding (grit) from - to 280 - 400
Finishing Recoatability: Can be coated over after sufficient drying time and intermediate sanding, e.g. with HB 65285-(colour tone), HDB 54705-(colour tone).
Yield per coat 8 - 14 m²/l

The spreading rate is heavily dependent on the type of application. The specifications relate to a liter of ready-for-use product, if necessary including hardener and thinner.
Storage temperature 10 - 30 °C
Working temperature 20 °C
conditions of transport 10 - 30 °C
Processing instructions Add hardener slowly whilst stirring. Adjust the spray viscosity with water if required. Maximum additive volume 5 %. The hardener must always be added before thinning! Never store product mixed with hardener in closed containers. Subsequent coating: after sufficient drying and sanding back, if required, apply another coat of the same product or suitable HYDRO or PU products. Clean tools with water. For removal of dried lacquer residues use Hesse HYDRO Cleaning agent HV 6917. In case of combined coatings (HYDRO- and solvent based lacquers) rinse application tools with Hesse HYDRO Reversing agent HV 6904. When directly coating cleaned or sanded foils, please apply a test coat to check the bonding!
Particular instructions This product must only be combined with other approved and technically suitable products when used as a flame retardant coating material for seagoing vessels according to the latest version of SOLAS 74/88 Reg. II-2/3, II-2/5 and II-2/6, IMO Resolution MSC.36(63)-(1994 HSC-Code) 7 and IMO Resolution MSC.97(73)-(2000 HSC-Code) 7. The maximum application amount in wet film when using this product as a flame retardant coating material for seagoing vessels is 140 g/m².

“A risk assessment was undertaken according to Directive 2014/90/EU, Annex II, Section 3. This coating does not pose a physical risk to health nor a risk to the environment when cured and dried.”
General instructions on workmanship With MDF coatings, you can avoid painting faults and edge breaks if you observe the following: Selection of a suitable MDF quality for the area of application, see manufacturer data on EU standard EN 622-5, pt. 4 Test method EN 317 (requirements on thickness swelling). Ideal panel moisture 5 - 7 %. If possible coat the MDF all around, the backs should at least receive a clear coating. Avoid sharp edges and cutaways, round-off wherever possible. Coat edges and cutaways 2x with primers, do not sand through, if need be, prime again. Thick boards that have been created by gluing together several thinner boards are, due to the variance in tension, susceptible to edge ridging. It is better to select a single MDF board of the appropriate thickness. Panels that have been glued together should always be sanded flat at the edges and colourlessly pre-insulated. Any water introduced by gluing must be allowed to evaporate prior to coating. Store primer-coated surfaces in an air conditioned location and apply the final coat in a timely manner.When working with HYDRO materials, parts that come into contact with the material must be made from stainless steel. The moisture content should be between 8 - 12 %. Do not apply or dry HYDRO lacquers at material or room temperatures below 18 °C. The ideal humidity for application lies between 55 and 65 %. During the lacquering process, a humidity level that is too low leads to surface defects (such as shrink cracks, etc.). Excessive humidity during the drying phase may drastically lengthen the drying time! In order to avoid adhesion problems, please sand the lacquered surfaces freshly before coating and apply lacquer to the sanded surfaces as soon as possible. When applied to foils, etc., please use a sample coating on the respective substrate to check the adhesion! The ideal complete hardening of lacquered surfaces that have been flashed off is reached at temperatures over 20 °C up to no more than 40 °C. Adequate, draft-free air exchange must be assured. The complete hardening of the lacquer will be reached after one week of proper storage (at least 20 °C room temperature). Woods containing large amounts of natural oils, such as teak, can negatively influence adhesion under certain circumstances. Water-soluble wood ingredients such those in ash and tannins in woods such as oak may cause colour changes and discolourations in the coating. We recommend that you always conduct a sample lacquering to evaluate the colour effect, adhesion and drying process under real conditions!

Kitchen furniture, MDF white, semi matt Sanding: grit 220 - 280 with subsequent dust removal. Basecoat: 2 x 130 - 150 g/m², HYDRO-PU Isolation primer HDP 5640-9343, mixing ratio (by volume) 7 : 1 with HYDRO-PU Hardener HDR 5081. Intermediate drying: at least 4 h / at 20 °C, better 16 h / at 20 °C room temperature and with adequate air circulation. Intermediate cutting back: in stages through grits 240 - 320 with subsequent dust removal. Finishing coat: 1 x 110 - 130 g/m² Hesse HYDRO-PU Color HDB 54705-9010, mixing ratio (by volume) 5 : 1 with HYDRO-PU Hardener HDR 5093. Packable: after drying for at least 16 h / 20 °C room temperature and with adequate air circulation.

Contact

Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.