Proterra Oil GE 11025-2001

  • Based on renewable raw materials
  • Solvent-free Without lead and cobalt containing drying agents
  • good grit accentuation
Oil based on linseed, low-solvent, therefore pleasant smelling, with no siccatives containing lead or cobalt, with good penetration characteristics for deep impregnation; for open-pored, vapour-permeable surfaces. With marked accentuation of the wood grit.
Request product Download data sheet
  • Description
  • Information on use
  • Sample process
  • Safety Data Sheets / Certificates

Fields of application

Surface treatment of woods in indoor areas such as living rooms / bedrooms and children's furniture, wall and ceiling paneling.

Technical specifications

Appearance colourless
Decopaint basis LB
Decopaint category F
Density series kg/l 0.949
Flow time 46 s / DIN EN ISO 2431 - 4 mm
Form of delivery fluid
Non-volatile content series % 98.5
Profile of properties
  • Highly elastic
  • Accentuated
VOC EU % 1.44 %
Number of coats (max) 2
Amount per layer (minimum) 10 g/m²
Amount per layer (max) 20 g/m²
Total application volume 40 g/m²

Information on use

Drying 16 h / 20 °C
Can be coated over within 24 h / 20 °C
Stackable after 16 - 24 h / 20 °C
Accessible after 16 h / 20 °C
Load bearing after 7 d / 20 °C
Mechanical drying Array
Surface preparation Clean, dry wood, free of oil, grease, wax and silicones. Sanded as prescribed and free from sanding dust.
Substrate sanding grits from-to 240 - 320
Finishing For coating the insides of cupboards, we recommend Proterra RESIT GE 17102 because of its low intrinsic smell. After suitable drying, can be re-coated with e.g. GZ 1020-0001, GZ 1622, GE 11025-2001, GE 12006-2001, GE 14004-2001.
Comments on sanding The quality and uniformity of the wood and of the lacquer sanding are crucial to the final surface finish. After sanding, remove dust as prescribed.
Yield per coat 47 - 95 m²/l

The spreading rate is heavily dependent on the type of application. The specifications relate to a liter of ready-for-use product, if necessary including hardener and thinner.
Storage temperature 10 - 30 °C
Working temperature 20 °C
Processing instructions Graduated raw-wood sanding with 240 - 320 grit with subsequent dust removal. Rub in with sanding fleece, allow to soak in briefly and remove excess with a cotton cloth. The surface should be dry; if not, drying problems may occur.
Particular instructions For coating the insides of cupboards, we recommend Proterra RESIT GE 17102 because of its low intrinsic smell. After suitable drying, can be re-coated with e.g. GZ 1020-0001, GZ 1622, GE 11025-2001, GE 12006-2001, GE 14004-2001.
The material dries with oxidation – please observe the general application instructions.
Skin may form due to the high reactivity. Please remove before agitating. Subsequently the material should be filtered as a precaution.
Storage class as per German Industrial Health and Safety Regulations (BetrSichV): Highly flammable. Please observe the latest version of the material safety data sheet!
General instructions on workmanship Materials with oxidative drying: a skin can form on the surface in containers, mainly opened containers. This should be removed prior to use. Low temperatures, increased ambient humidity, inadequate air exchange and wood contents that inhibit drying can extend the oil’s drying time.
The risk of spontaneous combustion means that coating substances generating heat during drying (oxidative drying oils) and coating substances forming highly flammable deposits may not be applied in the same spray booth without further precautions (see BGR 500, section 3: Handling different coating substances). Cotton cloths, cardboard and paper saturated with oil pose a risk of spontaneous combustion due to heat accumulation. They should therefore be spread out in the air to dry before being disposed of. Even oil-saturated wood dust is prone to spontaneous combustion; as a precaution please do not dispose of it in sealed containers and, where possible, do not use the spray booth for sanding. The oil itself does not combust spontaneously.
The necessary cleaning, care and refresh intervals should be matched to the number of layers of oil applied and the nature and intensity of use. The material properties have been tested on commonly available woods, such as oak, beech, etc. Resins in softwoods, coloured woods and exotic or unusual wood species can result in delayed drying and optical impairments. Please therefore check for suitability prior to use on such woods. Please also note that oils, like almost all natural materials, change colour over time under the influence of light and heat. Their colour can alter both under the influence of light (e.g. the sun’s UV rays, etc.) and due to light deprivation (yellowing at absence of light, e.g. beneath tablecloths, carpets, cabinets, etc.). This can become particularly apparent on brightly pigmented substrates. Oiled surfaces have a distinctive odour. This diminishes in a matter of days with progressive drying.

Natural beech shelving
Wood sanding: 240 - 280 grit with subsequent dust removal.
Use a fine sanding fleece to wipe in 1 x 10 - 20 g/m² Proterra Hard oil GE 11025-2001 and then use a cotton cloth to remove any excess.
Intermediate drying: at least 16 h / 20 °C room temperature with sufficient air circulation.
Use a fine sanding fleece to wipe in 1 x 10 - 20 g/m² Proterra Hard oil GE 11025-2001 and then use a cotton cloth to remove any excess.
Intermediate drying: at least 16 h / 20 °C room temperature and with sufficient air circulation.
The surface is then packable.

Contact

Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.