Fields of application
For all interior designs and for coating furniture.
Technical specifications
Appearance |
opaque
|
Density series kg/l |
0.956 - 1.157
|
Flow time (+/- 15 %) |
58 s / DIN 53211 - 4 mm
|
Form of delivery |
fluid
|
Non-volatile content series % |
0 - 55.3
|
Proportion of renewable raw materials % |
0 - 2.2485
|
VOC EU % |
46.91 %
|
Number of coats (max) |
2
|
Amount per layer (minimum) |
120 g/m²
|
Amount per layer (max) |
150 g/m²
|
Total application volume |
300 g/m²
|
Mixing ratio (by volume) |
10 : 1 Hardener RSR 90010
|
Mixing ratio (gravimetric) |
100 : 7 Hardener RSR 90010
|
Information on use
Usage time |
4 h / 20 °C.
|
Pot life |
5 d / 20 °C
|
Drying |
1 h / 20 °C
|
Stackable after |
> 30 min / 20 °C
|
Complete drying |
24 h / 20 °C
|
Surface preparation |
Clean, dry wood, clean suitable foil substrate or matching pigment filler. Free from oil, grease, wax and silicones. Correctly sanded and free from sanding dust.
|
Substrate sanding grits from-to |
120 - 400
|
Lacquer sanding (grit) from - to |
280 - 320
|
Finishing |
Recoatability: with itself following proper sanding.
|
Comments on sanding |
The quality and uniformity of the wood and of the lacquer sanding are crucial to the final surface finish. After sanding, remove dust as prescribed.
|
Yield per coat |
7 - 9 m²/l
The spreading rate is heavily dependent on the type of application. The specifications relate to a liter of ready-for-use product, if necessary including hardener and thinner.
|
Storage temperature |
10 - 35 °C
|
Working temperature |
20 °C
|
Processing instructions |
When used in spraying: Working viscosity: 22 - 24 s; where necessary up to 15 % addition of RSV 9993 is possible! To prevent drying delays due to increased ambient humidity, we recommend the addition of around 10 % RSV 9997 to the lacquer/hardener mixture rather than the usual thinner.
|
Particular instructions |
Due to its limited water resistance, do not use on open-pore structures for tables and worktops! Please apply a test coat under real conditions! Pre-priming is possible depending on the surface-finish requirements and substrate, for example with: RSP 94520-9343. Isolate content rich tropical wood beforehand with DG 4720-0001, DG 572-1. When directly coating cleaned or sanded foils, please apply a test coat to check the bonding! Storage class as per German Industrial Health and Safety Regulations (BetrSichV): Highly flammable. Please observe the latest version of the material safety data sheet!
|
General instructions on workmanship |
Reactive coatings should not be used or dried at material and room temperatures of less than 18 °C and below relative humidity of 40 %, ideal values: 20 - 25 °C, 50 - 65 % relative humidity. Deviations will result in drying or curing errors. In order to avoid problems with bonding, please sand the reactive lacquers before applying fresh lacquer and apply lacquer to the sanded surfaces as soon as possible. The final hardening of the lacquer will be reached after one week of proper storing (at least 20 °C room temperature). Please apply a test coat under real conditions!
|
The coating process and the precise treatment parameters are adapted in each case to the respective application and drying conditions and can be found in the customer-specific process descriptions (surface techniques).
Material Safety Data Sheets
Contact
Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always
available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge
available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our
terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.